+91 8777212335

info@genuineent.in

81, Netaji Subhas Road, 3rd Floor, Room No. 306,
Century Plaza, Kolkata-700001

+91 8777212335

info@genuineent.in

© Copyright 2026, Genuine Enterprises. All rights reserved. Powered by Hats-Off

HT 900-1

HT 900

+91-8777212335

Short Description

Every toolroom has a few bits that get picked up again and again, and the HT 900 is built to be one of them. It is a solid square-section high-speed steel blank, hardened and ground so it can be shaped into whatever cutting edge a job demands. Turners use it for everyday facing and turning work, while toolmakers grind it into custom profiles for parting, grooving, and form cutting. Nothing about it is complicated. It is a straightforward bar of steel that holds its edge and takes regrinding well, which is really all a good tool bit needs to do.

  • Material: made from high-speed steel (HSS), a tool steel known for holding hardness at cutting temperatures.
  • Common grades: typically produced in grades such as M2, giving a good balance of toughness and wear resistance.
  • Hardness: generally falls between 62 and 66 HRC after heat treatment.
  • Shape: straight square cross-section bar, sold as blanks ready for grinding.
  • Size range: offered in a range of inch and metric square sizes to suit different tool holders.
  • End finish: ground with a standard bevel angle so the bit is ready for shaping into the required cutting geometry.
  • Tolerance: held to a close square tolerance for a stable fit in the tool holder.

Key Features

  • Solid square high-speed steel bar stock
  • Hardened for edge retention during cutting
  • Ground surface for easy reshaping and resharpening
  • Fits standard square tool post holders
  • Handles turning, facing, parting, and threading work
  • Cuts cleanly through mild steel and cast iron
  • Retains hardness under the heat of continuous machining
  • Available in a range of square sizes and lengths

Applications of Square Tool Bits HT 900

  • Turning operations on centre lathes
  • Facing cuts on rotating workpieces
  • Parting and cut-off tasks
  • Thread cutting on manual lathes
  • Boring bar tip fabrication
  • Shaper machine tooling
  • Planer cutting tool setups
  • Fly cutter blanks for milling
  • Custom ground profile tools
  • Apprentice and training workshop use

Advantages of Square Tool Bits HT 900

  • Keeps a sharp edge through repeated cuts
  • Can be reground several times before it needs replacing
  • Slots into standard tool holders without adjustment
  • Works across a range of common workshop metals
  • Handles the heat of continuous machining without softening quickly
  • Cuts down on how often the tool needs changing mid-job

Why Choose Genuine Enterprises

We grind every batch of tool bits with a close eye on straightness and hardness, because a bit that is even slightly off can throw off an entire cutting job. Our production process is built around consistency, so one bar behaves the same way as the last one you ordered. That kind of steady quality matters more in a busy workshop than most people realise.

 

The HT 900 is produced with attention to the finer details that machinists actually care about, from surface finish to squareness. We keep stock ready to move so tooling shortages do not slow down your production line. Whether you need a handful of pieces or a bulk order, our team is set up to handle it without unnecessary back and forth.

1.What material is the HT 900 tool bit made from? 

It is made from high-speed steel, which is chosen for its ability to stay hard even when the cutting edge heats up.

2. Is the HT 900 suitable for beginners in a workshop? 

Yes, its straightforward square shape and standard sizing make it easy to work with for both trainees and experienced machinists.

3. How many times can the HT 900 be reground? 

It can be reground several times over its life, depending on how much material is removed with each sharpening.

4. What kind of lathe work is the HT 900 used for? 

It handles turning, facing, parting, and threading, covering most of the everyday cuts made on a centre lathe.

5. Does the HT 900 come in different sizes? 

Yes, it is available in a range of square cross-sections and lengths to match different tool holders and job requirements.

Chat With Us