+91 8777212335

info@genuineent.in

81, Netaji Subhas Road, 3rd Floor, Room No. 306,
Century Plaza, Kolkata-700001

+91 8777212335

info@genuineent.in

© Copyright 2026, Genuine Enterprises. All rights reserved. Powered by Hats-Off

HT 1000-1

HT 1000

+91-8777212335

Short Description

Machinists who spend long hours at the lathe know that a cutting tool is only as good as the steel behind it, and that is exactly where the HT 1000 earns its place on the tool post. This is a square-section high-speed steel bit, ground and hardened to hold a keen edge through repeated turning, facing, and parting cuts on mild steel, alloy steel, and cast iron. It is shaped as a solid square bar so it can be reground into whatever profile a job calls for, from a simple turning point to a custom form tool. For workshops that run their lathes hard, HT 1000 is built to take the heat and keep cutting cleanly.

  • Material: manufactured from high-speed steel (HSS), commonly in grades such as M2 or M35 depending on the cutting application.
  • Hardness: typically falls in the 62 to 66 HRC range once heat-treated.
  • Shape: square cross-section, supplied as straight bar stock.
  • Size range: available from small fractional sizes up to larger square sections, in both inch and metric dimensions.
  • Bevel angle: ground with a standard end bevel, commonly around 15 degrees, ready for grinding into the required tool geometry.
  • Tolerance: held to a close dimensional tolerance, often around h13, for a snug fit in tool holders.
  • Finish: supplied with a ground surface finish for straightforward regrinding at the workshop.

Key Features

  • Made from high-speed steel for heat resistance during continuous cuts
  • Precision-ground square profile for consistent seating in standard tool holders
  • Holds a sharp cutting edge through repeated resharpening
  • Suitable for turning, facing, threading, and parting operations
  • Available in a wide range of square cross-sections and lengths
  • Works well on mild steel, alloy steel, tool steel, and cast iron
  • Resists softening at the elevated temperatures generated during cutting
  • Ground to close dimensional tolerances for accurate tool holder fit

Applications of Square Tool Bits HT 1000

  • General turning on centre lathes
  • Facing operations on metal workpieces
  • Parting and cut-off work
  • Thread cutting on lathes
  • Boring bar tooling in machine shops
  • Shaping machine tooling
  • Planer machine cutting tools
  • Fly cutter and milling blank fabrication
  • Custom ground form tools for specific profiles
  • Toolroom and workshop training setups

Advantages of Square Tool Bits HT 1000

  • Withstands the heat generated during continuous machining
  • Can be reground multiple times before replacement is needed
  • Fits standard square tool holders without modification
  • Handles a wide range of metals without frequent edge failure
  • Keeps its shape and hardness under repeated use
  • Reduces the need for frequent tool changes during a job

Why Choose Genuine Enterprises

Every batch of HT 1000 that leaves our facility goes through careful checks on hardness, straightness, and surface finish before it reaches a customer. We understand that a tool bit sitting slightly out of tolerance can throw off an entire job, so we treat dimensional accuracy as non-negotiable. Our team works closely with machine shops to understand how these bits are actually used on the floor, not just how they look on a spec sheet.

 

As an HT 1000 supplier in India, we ship to workshops of every size, from single-machine setups to full production floors. Orders are packed to prevent damage in transit and dispatched promptly so tooling delays do not hold up production schedules. We also work with buyers on custom sizes and quantities when standard stock does not fit the job.

1.What is the HT 1000 tool bit made from? 

It is made from high-speed steel, a material chosen for its ability to hold a cutting edge at elevated temperatures.

2. Can the HT 1000 be reground after it wears down? 

Yes, it can be reground into fresh cutting profiles multiple times, which extends its usable life well beyond the first sharpening.

3. What machines is this tool bit used on? 

It is commonly used on centre lathes, shaping machines, and planers for turning, facing, parting, and threading work.

4. What materials can the HT 1000 cut? 

It is suited to mild steel, alloy steel, tool steel, and cast iron, covering most general machining needs in a workshop.

5. Do you offer custom sizes of the HT 1000? 

Yes, alongside standard square sections and lengths, we can discuss custom sizing based on your specific tooling requirements.

Chat With Us